My Freeplay CM3+ Slim Internal Look

Checking out the internals of my Freeplay CM3+ Slim build while overusing the words “Hot Glue,” “Finicky,” and “Relocated.”

https://www.freeplaytech.com

The Magnet Wire:

https://www.amazon.com/gp/product/B00L5IUCYA/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

I first saw magnet wire in this really cool video of a Pokédex handheld.

The Ribbon Cable Connector:
This is not where I purchased mine; my exact purchase isn’t available anymore, but these LOOK like the exact same ones I used. I think I’d grab a 5 pin variant if I could find one though for a better fit.

https://www.ebay.com/itm/10-X-FPC-FFC-0-5mm-Pitch-10-Pin-Flip-Type-Flat-Cable-Connector-Bottom-Contact-OJ/163081970947?ssPageName=STRK%3AMEBIDX%3AIT&var=462219980380&_trksid=p2057872.m2749.l2649

The speakers:
It looks like these are currently unavailable, but it will give you an example at least. I’d do some research to see if there are more powerful options too. These get the job done, but are not great. Putting 2 additional rear firing would help out.

https://www.amazon.com/gp/product/B0798RDPXD/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

Joy Cons:
I just purchased mine in a 5 pack on eBay (listing not available anymore) for $15.99 if I remember right. They are pretty abundant so you just have to do a bit of searching. I’m thinking about another Slim build with some upgrades, and might even try out some new sticks. Maybe 3DS sticks.

Copper Tape;
BCP Single-sided Conductive EMI Shielding Copper Foil Tape- 1/4 Inch X 55 Yds https://www.amazon.com/dp/B01DVZ1G1C/ref=cm_sw_r_cp_tai_PXUJCbWZQGPR3

3D Printed Port Cover:
You can just use any piece of thin anything really. Just make the port cutouts as clean as possible and get the clean look. I use this port cover and cut of everything from the flat piece so I can sink it into the case.

https://www.thingiverse.com/thing:3024005

Kapton Tape;
ProTapes Pro 950 Polyimide Film Tape, 7500V Dielectric Strength, 36 yds Length x 1/2″ Width (Pack of 1) https://www.amazon.com/dp/B00DVBLKZE/ref=cm_sw_r_cp_tai_.-OJCbET57GT5

Epoxy:
I use JB Weld for the same kind of reasons people (me too) use Duct Tape/Gorilla Tape on everything. So there DEFINITELY must be an actual correct better way to make body filler or connect pieces of plastic. I just want to say that I use JB Weld without having researched possible better options YET. I’ve tried a few kinds and this one is the strongest I’ve found. The downside is that it takes along time to set.https://www.amazon.com/J-B-Weld-8265S-Original-Reinforced/dp/B01FWGF9L6/ref=sr_1_3?keywords=jb+weld&qid=1552842790&s=electronics&sr=1-3-catcorr

The 4.6nF Capacitor:
I just noticed that I used a 4.7nF capacitor. Well I guess it’s close enough

https://www.ebay.com/itm/10pcs-10x-1000V-4-7nF-High-Voltage-Ceramic-Capacitor-472M-1KV-0047uF-4700pF/253517115640?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

The Glass Screen:
I’ve been searching my emails for the order and haven’t found it. The glass was just a blank glass Game Boy Advance screen cover. I saw a post on the Freeplay site that showed the maker had scratched away the coloring on the glass Freeplay screen to widen up the space for the full screen mod. So you could check out modding the glass screen in that way, or I bet something like acetone would help remove the coloring completely. If I find the exact information for my purchase I’ll add it here.

Soft Tact Switches:

https://www.adafruit.com/product/3101?gclid=EAIaIQobChMIrvrr49yJ4QIVgzxpCh2aKg6XEAQYASABEgIb-fD_BwE

Tact Switches:
The exact listing for my order isn’t available. These LOOK like the ones I used, but the button caps on mine are slightly more rounded I think. I don’t know about this seller or anything. I just did a quick search to show an example, so search around a bit. The button caps can help you shorten or lengthen the button too. You can cut/file a little of the button post (not too much because the post tends to be hollow near the bottom I’ve found) to make it shorter, and you can just glue the cap on and hold it higher up while it dries to make it longer.

https://www.ebay.com/itm/20-Pcs-6x6x12mm-4pin-Push-Button-Micro-Tactile-Tact-Switch-with-Cap-K9L9/253030644600?epid=8004733877&hash=item3ae9cd3b78:g:mgsAAOSwvjdZXcEZ

You can also find tact switch assortments like this one (I haven’t purchased this and I don’t know about the seller):

https://www.ebay.com/itm/10-Values-180PCS-Tactile-Push-Button-Switch-Mini-Momentary-Tact-Assortment-I6J1/182948831180?epid=28010007799&hash=item2a98999fcc:g:4dMAAOSwke9aJ-Re

The Leathery Textured Decal:
It’s some left over material from a MacBook palm rest kind of decal. Just scrap I had lying around. I’ll show the link, but I’m not suggesting anyone buy a MacBook palm rest decal to use on their system

https://www.ebay.com/itm/2-packs-Wrist-Palm-Rest-Cover-Skin-Protector-for-Apple-Macbook-Retina-12-2015/323708446611?hash=item4b5e86e793:m:maqc2gzkSfo8PixOARtCrAg